• 不銹鋼9-19高壓離心風機

  9-19型高壓離心式通風機一般用于鍛冶爐及高壓強制通風機，可廣泛用于輸送物料，輸送空氣及無腐蝕性不自然，不含粘性物質及氣體。介質溫度一般不超過50℃（最高不超過80℃）。介質中所含塵土及顆粒不大于150mg/m³。
  產品型式:本廠機號有NO3.15、3.55、4、4.5、5、5.6、6.3、7.1八種。可制成右旋和左旋兩種型式，葉輪順時針旋轉，稱為右旋風機。以“右”表示，葉輪逆時針旋轉，稱為左旋風機，以“左”表示。風機的出口位置，以機殼的出風角度表示，9-19型風機NO3.15~7.1出廠時均做成多種型式，可根據使用單位要求安裝成所需的位置，即出風口位置調整范圍0°~225°或45°，即（0°、45°、90°、135°、180°、225°）共六種。NO7.1根據用戶需求制成一種方向角度。風機的傳動方式為A式（NO3.15~6.3）和D式NO7.1兩種。
  結構特點:本風機主要由葉輪、機殼、進風口、機架、底架、軸承箱等皮帶傳動而組成。葉輪：由10個后傾的機翼型葉片、曲線型前盤和平板后盤組成，并經過動平衡校正，氣動性能，故運轉平衡、振動小、效率高、壽命長等特點。機殼：用鋼板焊成蝸型殼體。進風口：制成整體（全部模具成型），裝于風機的側面，于軸向平行的戴面為曲線形狀，能使氣體順利進入葉輪，且損失較小。傳動組：由主軸、軸承箱、聯軸器等。主軸由優質鋼制成，軸承箱整體結構，采用滾動軸承，分為水冷和油冷兩種。

• High pressure centrifugal fan

  9-19 high pressure centrifugal fan is generally usedforforging furnace and high pressure forced fan, can bewidely used in conveying materials, conveying air andnon-corrosive nature, non-sticky substances and gases. The medium temperature is generally not more than 50℃ with maximum below80℃. The concentration of mediacontaining dust and particles is not more than 150mg/m³.Product type: The factory number is NO3.15, 3.55, 4, 4.5, 5, 5.6, 6.3, 7.1. It can be made into two types: right-handed and left-handed. The impeller rotates clockwise and is called a right-handed fan. Expressed as "right", the impeller rotates counterclockwise, called the left-handed fan, and is represented by "left". The outlet position of the fan is expressed by the air outlet angle of the casing. The 9-19 type fan NO3.15~7.1 is made into various types when it leaves the factory. It can be installed to the required position according to the requirements of the unit, that is, the position of the air outlet is adjusted. The range is 0°~225° or 45°, that is, (0°, 45°, 90°, 135°, 180°, 225°). NO7.1 is made into a direction angle according to user requirements. The transmission mode of the fan is A type (NO3.15~6.3) and D type NO7.1.Structural features: The fan is mainly composed of impeller, casing, air inlet, frame, chassis, bearing box and other belt drives. Impeller: It consists of 10 backward-inclined airfoil blades, curved front plate and flat rear plate. It has dynamic balance correction and aerodynamic performance, so it has the characteristics of balanced operation, small vibration, high efficiency and long service life. Housing: welded with a steel plate into a volute casing. Air inlet: made into a whole (all mold molding), installed on the side of the fan, and the axially parallel wearing surface has a curved shape, which enables the gas to smoothly enter the impeller with less loss. Transmission group: from the main shaft, bearing housing, coupling and so on. The main shaft is made of high-quality steel. The overall structure of the bearing housing is made of rolling bearings and is divided into water-cooling and oil-cooling.

產品為人工實物測量會有一定誤差，相關數據僅作參考，以收到的實物為準。 單位Unit: mm(毫米）